
Broadcom Corporation Confidential.
For
Evaluation Use Only.
|
SECTION 5.0: AP TEST CONFIGURATIONS - WPA+802.11g |
|
|
|
|
|
|
|
|
5.1.1 OOB Verification |
Pass |
|
5.1.2 Configurability Test |
|
|
- Turn WPA on or off |
Pass |
|
- When WPA is on, verify PSK or TLS can be selected |
Pass |
|
- Multicast/unicast keys & mixture of WPA/WPA cannot be selected |
Pass |
|
- Spefigy SSID string |
Pass |
|
- Specify default pass phrase ("12345678") forWPA-PSK can be configured |
Pass |
|
5.1.3 WPA Initial Ping Test |
|
|
- APs: Security: WPA-TLS, Ch: 11, Server: Funk |
|
|
- STAUT: on Win2K using Funk supplicant |
|
|
- Atheros AP |
Pass |
|
- Broadcom AP |
Pass |
|
- Globespan AP |
Pass |
|
- Proxim AP |
Pass |
|
- TI AP |
Pass |
|
5.2.2.1 - Configuration #S1-Pure G --- Broadcom-G AP |
|
|
- (ESSID: a, WEP: off, Ch: 1, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K |
|
|
- Data Transfer 1: FileSendLong Tx - S1GDT1 [13.02] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S1GDT2 [13.32] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S1GDT3 [1.05] |
Pass |
|
- Data Transfer 2(NAV): if throughput less than 80% of throughput measured in DT#2 |
Pass |
|
- Data Transfer 2(PLCP): if throughput less than 80% of throughput measured in DT#2 |
Pass |
|
5.2.2.2 - Configuration #S1-Pure B --- Cisco-B AP |
|
|
- (ESSID: a, WEP: off, CH: 2, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K |
|
|
- Data Transfer 1: FileSendLong Tx - S1BDT1 [3.64] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S1BDT2 [3.63] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S1BDT3 [0.66] |
Pass |
|
5.2.2.3 - Configuration #S1-Mix BG --- Glopespan-G AP |
|
|
- (ESSID: a, WEP: off, CH: 3, B-Rates: 1, 2, 5.5, 11, Beacons: 50, RTS: off, Frag: off): STA on Win2K |
|
|
- STA B Values: Atheros-G in 802.11b only mode, RTS: 256, Frag: 500 |
|
|
- Data Transfer 1: FileSendLong Tx - S1MGDT1 [3.93] |
Pass |
|
- S1MBDT1 [1.50] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S1MGDT2 [5.36] |
Pass |
|
- S1MBDT2 [0.30] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S1MGDT3 [0.61] |
Pass |
|
- S1MBDT3 [0.07] |
Pass |
|
5.2.2.4 - Configuration #S2-Pure G --- Globespan-G AP |
|
|
- (ESSID: abcdefghijklmnopqrstuvwxyzABCDEF, WEP: PSK_12345678, Supplicant: MS, CH: 4, |
|
|
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: 500): STA on WinXP |
|
|
- Data Transfer 1: FileSendLong Tx - S2GDT1 [8.12] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S2GDT2 [7.10] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S2GDT3 [0.70] |
Pass |
|
5.2.2.5 - Configuration #S2-Pure B --- Cisco-B AP |
|
|
- (ESSID: 12345678901234567890123456789012, WEP: PSK_12345678, Supplicant: MS, CH: 5, |
|
|
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: 256, Frag: off): STA on WinXP |
|
|
- Data Transfer 1: FileSendLong Tx - S2BDT1 [3.25] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S2BDT2 [3.30] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S2BDT3 [0.50] |
Pass |
|
5.2.2.6 - Configuration #S2-Mix BG --- Broadcom-G AP |
|
|
- (ESSID: abcdefghijklmnopqrstuvwxyzABCDEF, WEP: PSK_12345678, Supplicant: MS, CH: 6, |
|
|
B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: off) |
|
|
- STA B Values: Globespan-B, RTS: off, Frag: 500 (STA on WinXP) |
|
|
- Data Transfer 1: FileSendLong Tx - S2MGDT1 [3.00] |
Pass |
|
- S2MBDT1 [2.60] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S2MGDT2 [2.30] |
Pass |
|
- S2MBDT2 [0.36] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S2MGDT3 [0.42] |
Pass |
|
- S2MBDT3 [0.43] |
Pass |
|
5.2.2.7 - Configuration #S3-Pure G --- TI-G AP |
|
|
- (ESSID: space here, WEP: 0x9876543210, CH: 7, B-Rates: 1, 2, 5.5, 11, 6, 12, 24, |
|
|
Beacons: 200, RTS: off, Frag: off): STA on Win2K |
|
|
- Data Transfer 1: FileSendLong Tx - S3GDT1 [13.42] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S3GDT2 [12.62] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S3GDT3 [0.88] |
Pass |
|
5.2.2.8 - Configuration #S3-Pure B --- Cisco-B AP |
|
|
- (ESSID: space here, WEP: 0x9876543210, CH: 8, B-Rates: 1, 2, 5.5, 11, Beacons: 200, |
|
|
RTS: off, Frag: 500): STA on Win2K |
|
|
- Data Transfer 1: FileSendLong Tx - S3BDT1 [2.25] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S3BDT2 [3.63] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S3BDT3 [0.64] |
Pass |
|
5.2.2.9 - Configuration #S3-Mix BG --- TI-G AP |
|
|
- (ESSID: space here, WEP: 0x9876543210, CH: 9, B-Rates: 1, 2, 5.5, 11, Beacons: 200, |
|
|
RTS: off, Frag: off) |
|
|
- STA B Values: Globespan-B, RTS: 256, Frag: off (STA on Win2K) |
|
|
- Data Transfer 1: FileSendLong Tx - S3MGDT1 [3.70] |
Pass |
|
- S3MBDT1 [2.45] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S3MGDT2 [2.54] |
Pass |
|
- S3MBDT2 [0.40] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S3MGDT3 [0.50] |
Pass |
|
- S3MBDT3 [0.39] |
Pass |
|
5.2.2.10 - Configuration #S4-Pure G --- Proxim-G AP |
|
|
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS CH: 10, B-Rates: 1, 2, 5.5, 11, 6, 12, 24, |
|
|
Beacons: 500, RTS: 256, Frag: 500): STA on WinXP |
|
|
- Data Transfer 1: FileSendLong Tx - S4GDT1 [8.27] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S4GDT2 [12.0] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S4GDT3 [1.05] |
Pass |
|
5.2.2.11 - Configuration #S4-Pure B --- Cisco-B AP |
|
|
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS, CH: 11, B-Rates: 1, 2, 5.5, 11, Beacons: 500, |
|
|
RTS: 256, Frag: 500): STA on WinXP |
|
|
- Data Transfer 1: FileSendLong Tx - S4BDT1 [2.50] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S4BDT2 [2.19] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S4BDT3 [0.50] |
Pass |
|
5.2.2.12 - Configuration #S4-Mix BG --- Proxim-G AP |
|
|
- (ESSID: a, WEP: WPA-TLS, Supplicant/Server: MS/MS, CH: 11, B-Rates: 1, 2, 5.5, 11, Beacons: 500, |
|
|
RTS: Off, Frag: off): STA on WinXP |
|
|
- STA B Values: Intel-B, RTS: off, Frag: off |
|
|
- Data Transfer 1: FileSendLong Tx - S4MGDT1 [2.80] |
Pass |
|
- S4MBDT1 [1.80] |
Pass |
|
- Data Transfer 2: FileSendLong Rx - S4MGDT2 [2.80] |
Pass |
|
- S4MBDT2 [2.06] |
Pass |
|
- Data Transfer 3: InquiryLong Tx - S4MGDT3 [0.40] |
Pass |
|
- S4MBDT3 [0.25] |
Pass |
|
5.3.1 - WPA Same Mode Roaming with an Authentication Server |
|
|
- (ESSID: roaming, WEP: WPA-TLS, Supplicant/Server: Funk/Funk, Ch:8, Frag/RTS: Off): STA on Win2K |
|
|
- Globespan-G(AP2) |
Pass |
|
- TI-G(AP3) |
Pass |
|
- Proxim-G(AP4) |
Pass |
|
5.3.2 - WPA Same Mode Roaming using Pre-Shared Keys |
|
|
- (ESSID: roaming, WEP: PSK_12345678, Supplicant: Funk, Ch:9, Frag/RTS: Off): STA on Win2K |
|
|
- Globespan-G(AP2) |
Pass |
|
- TI-G(AP3) |
Pass |
|
- Proxim-G(AP4) |
Pass |
|
5.4.1 - Configuration #MCS1 --- Broadcom-G AP Values: (ESSID: Multicast, WEP: 0x0123456789, |
|
|
CH: 8, B-Rates: 1, 2, 5.5, 11, Beacons: 100, RTS: off, Frag: off) |
|
|
- STAUT(G-STA-MC-1)on Win2K: All Default --- Atheros-G STA(G-STA-MC-2): All Default |
|
|
- Data Transfer: Realaud Rx |
Pass |
|
5.4.2 - Configuration #MCS2 --- Proxim-G AP Values: (ESSID: Multicast, WEP: PSK_0123456789, |
|
|
Supplicant: MS, CH: 11, B-Rates: 1, 2, 5.5, 11, 6, 12, 24, Beacons: 150, RTS&Frag: off) |
|
|
- STAUT(G-STA-MC-1) on Win2XP: All Default --- TI-G STA(G-STA-MC-2): Power Save: PSPOLL |
|
|
- Data Transfer: Realaud Rx |
Pass |
|
5.5 Negative Tests |
|
|
- Wrong ESSID: |
Pass |
|
- Wrong Case in ESSID: |
Pass |
|
- ESSID Substring: |
Pass |
|
- WEP key mismatch: |
Pass |
|
- Station/AP WEP mismatch: |
Pass |
|
5.6.1 STA Countermeasures |
|
|
- After the first bad frame STA continues to ping |
Pass |
|
- After the second bad frame STA continues to ping |
Pass |
|
- After the third bad frame STA deauthenticates and pings stop |
Pass |
|
- After 60 seconds the STA can associate and the ping session resumes |
Pass |
|
5.6.2.1 STA WPA Negative Tests: Non-Association with a WEP AP(Proxim) |
|
|
- ESSID: wpa, WEP: 9876543210, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off |
|
|
- STAUT on WinXP: Configure for WPA-TLS |
|
|
- Verify the STA does not receive a ping response from the authenticaton server |
Pass |
|
5.6.2.1 STA WPA Negative Tests: Non-Association with an AP not using WPA(Proxim) |
|
|
- ESSID: wpa, WEP: Off, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off |
|
|
- STAUT on WinXP: Configure for WPA-TLS |
|
|
- Verify the STA does not receive a ping response from the authenticaton server |
Pass |
|
5.6.2.3.1 STA WPA Negative Tests: Non-Association with a PSK configured station(Broadcom) |
|
|
- ESSID: wpa, WEP: WPA-TLS, Server: MS, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off |
|
|
- STAUT on WinXP: configured for WPA-PSK: 12345678 |
|
|
- Verify an Atheros STA configured for WPA-TLS can associate and can ping the server |
Pass |
|
- Verify the STA does not receive a ping response from the authenticaton server |
Pass |
|
5.6.2.3.2 STA WPA Negative Tests: Non-Association with a TLS configured station(Broadcom) |
|
|
- ESSID: wpa, WEP: PSK_12345678, Ch: 11, B-Rate: 1, 2, 5.5, 11, Beacons: 100; Frag/RTS: Off |
|
|
- STAUT on WinXP: configured for WPA-TLS |
|
|
- Verify an Atheros STA configured for WPA-PSK can associate and can ping the server |
Pass |
|
- Verify the STA does not receive a ping response from the authenticaton server |
Pass |
|
SECTION 6.0: IBSS TEST CONFIGURATIONS WPA+802.11g |
|
|
|
|
|
6.1.1 - Active Scan Tests |
|
|
Creator STA = Station Under Test (ESSID: active scan, WEP: off, CH: 1, all else default) |
Pass |
|
Join STA = Atheros-G---> (Frag: 384); (RTS: Off) |
Pass |
|
Verify SUT responds with a valid response to probe |
Pass |
|
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps |
Pass |
|
Verify the channel in beacon frame is correct |
Pass |
|
Verify EID=42 and EID=50 are NOT present in the beacon message |
Pass |
|
Verify BSSID is a random value after restart |
Pass |
|
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI1DT1 [1.8] |
Pass |
|
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI1DT2 [3.5] |
Pass |
|
6.2.1 - Passive Scan Tests |
|
|
Creator STA = Station Under Test (ESSID: passive scan, WEP: 0x1122334455, CH: 11, Frag: off, RTS: off) |
Pass |
|
Join STA = Atheros-G---> (Frag: off, RTS: 300) |
Pass |
|
Verify SUT responds with a valid response to probe |
Pass |
|
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps |
Pass |
|
Verify the channel in beacon frame is correct |
Pass |
|
Verify EID=42 and EID=50 are NOT present in the beacon message |
Pass |
|
Verify BSSID is a random value after restart |
Pass |
|
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI2DT1 [1.7] |
Pass |
|
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI2DT2 [3.4] |
Pass |
|
6.3.1 - IBSS WEP on Tests |
|
|
Creator STA = Globespan-G (ESSID: IBSS wep on, WEP: 0xdeadbeef12, CH: 4, B-Rates: 1, 2, 5.5, 11, |
Pass |
|
S-Rates: 1, 2, 5.5, 11, Frag: off, RTS: Off) |
Pass |
|
Joiner STA1 = Buffalol-G---> (Frag: off, RTS: 300) |
Pass |
|
Joiner STA2 = STA Under Test ---> (All default) |
Pass |
|
Verify SUT responds with a valid response to probe |
Pass |
|
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps |
Pass |
|
Verify the channel in beacon frame is correct |
Pass |
|
Verify EID=42 and EID=50 are NOT present in the beacon message |
Pass |
|
User sniffer to capture a trace for 2 minutes and verify beacons fairly distributed between stations |
Pass |
|
Data Transfer #1: FileSendLong from Buffalo-G to SUT - SI3DT1 [3.2] |
Pass |
|
Data Transfer #2: FileSendLong from SUT to Buffalo - SI3DT2 [3.5] |
Pass |
|
Data
Transfer #3: Multicast Realaud - SI3DT3 [0.06] |
Pass |
|
Data
Transfer #4: Multicast Realaud - SI3DT4 [0.06] |
Pass |
|
6.4.1 - IBSS WEP off Tests |
|
|
Creator STA = Atheros-G (ESSID: IBSS wep off, WEP: off, CH: 8, B&S Rates: Default, Frag&RTS: off) |
Pass |
|
Joiner STA1 = Buffalo-G---> (Frag: 400, RTS: 300) |
Pass |
|
Joiner STA2 = STA Under Test ---> (All default) |
Pass |
|
Verify SUT responds with a valid response to probe |
Pass |
|
Verify basic rates enumerated in the beacons are only 1, 2, 5.5 and 11 Mbps |
Pass |
|
Verify the channel in beacon frame is correct |
Pass |
|
Verify EID=42 and EID=50 are NOT present in the beacon message |
Pass |
|
User sniffer to capture a trace for 2 minutes and verify beacons fairly distributed between stations |
Pass |
|
Data Transfer #1: FileSendLong from Atheros-G to SUT - SI4DT1 [3.5] |
Pass |
|
Data Transfer #2: FileSendLong from SUT to Atheros-G - SI4DT2 [3.5] |
Pass |
|
Data Transfer #3: FileSendLong from Buffalo-G to SUT - SI4DT3 [1.9] |
Pass |
|
Data Transfer #4: FileSendLong from SUT to Buffalo-G - SI4DT4 [3.5] |
Pass |
|
6.5.1 Re-Join Tests |
|
|
Creator STA = Globespan-G (ESSID: coalesce, WEP: off, CH: 11, B&S Rates: Default, Frag: off, RTS: off) |
Pass |
|
Joiner STA1 = TI-G---> (Frag: off, RTS: off, all else default) |
Pass |
|
Joiner STA2 = STA Under Test ---> (CH: 11, Frag: off, RTS: off, all else default) |
Pass |
|
Move SUT out of range and verify not receiving beacons |
Pass |
|
Move SUT back into range, verify connection to 3 STAs |
Pass |
|
WIFI WPA AP
Test Configurations |
|
|
4.1 Out of the box
Verification |
Pass |
|
4.3 Configuration
Paramters |
|
|
- Turn WPA on or
off |
Pass |
|
- When WPA is on, Verify PSK of
TLS can be selected |
Pass |
|
- Multicast/unicast keys &
mixture of WPA/WEP cannot be selected |
Pass |
|
- Specify SSID
string |
Pass |
|
- Specify default pass phrase
("12345678") for PSK WPA |
Pass |
|
5.0 Initial Ping Test - Win2K
& Funk 802.1x Supplicant in EAP-TLS |
|
|
- Atheros AR5BAP - 00025A
(AP1) |
Pass |
|
- Cisco AIR-AP1230B
(AP2) |
Pass |
|
- Broadcom AP BCM4306
(AP3) |
Pass |
|
- Intersil PRISM ISL36356A
(AP4) |
Pass |
|
6.1 Same Mode Roaming with
Authentication Server - Win2k & Funk |
|
|
- Cisco AIR-AP1230B
(AP2) |
Pass |
|
- Broadcom AP BCM4306
(AP3) |
Pass |
|
- Intersil PRISM ISL36356A
(AP4) |
Pass |
|
6.2 Same Mode Roaming Using
Pre-Shared Keys - Win2K & Funk |
|
|
- Cisco AIR-AP1230B
(AP2) |
Pass |
|
- Broadcom AP BCM4306
(AP3) |
Pass |
|
- Intersil PRISM ISL36356A
(AP4) |
Pass |
|
7.2 STA Countermeasures -
Win2K |
|
|
1. The Access Point generates a
single bad frame |
Pass |
|
- Verify the STA continues to ping for the next 70
seconds |
Pass |
|
2. The access Point generates a
second bad frame |
Pass |
|
- Verify the STA continues to ping for the next 50
seconds |
Pass |
|
3. The Access Point generates a
third bad frame |
Pass |
|
- Verify the STA deauthenticate the pings
stops |
Pass |
|
4. Verify the STA could only
reassociate after 60 seconds |
Pass |
|
9.1.1 STA Point-to-point
Throughput - XP |
|
|
a. WPA -
EAP-TLS |
Pass |
|
- S1DT1 [4.0Mbps] - Cisco 1230B |
Pass |
|
- S1DT2 [3.5Mbps] - Cisco 1230B |
Pass |
|
- S1DT3 [0.2Mbps] - Cisco 1230B |
Pass |
|
- S2DT1 [1.5Mbps] - Broadcom AP
BCM4306 |
Pass |
|
- S2DT2 [3.5Mbps] - Broadcom AP
BCM4306 |
Pass |
|
- S2DT3 [0.3Mbps] - Broadcom AP
BCM4306 |
Pass |
|
b.
WPA-PSK |
Pass |
|
- S1DT1 [4.0Mbps] - Cisco 1230B |
Pass |
|
- S1DT2 [3.5Mbps] - Cisco 1230B |
Pass |
|
- S1DT3 [0.2Mbps] - Cisco 1230B |
Pass |
|
- S2DT1 [1.5Mbps] - Broadcom AP
BCM4306 |
Pass |
|
- S2DT2 [3.5Mbps] - Broadcom AP
BCM4306 |
Pass |
|
- S2DT3 [0.3Mbps] - Broadcom AP
BCM4306 |
Pass |
|
9.1.2 STA Multicast
Throughput - Using Cisco 1230B - XP |
|
|
a. WPA -
EAP-TLS |
Pass |
|
- SUT sends multicast data stream to
STA2(Intersil) |
Pass |
|
- STA2 sends mulitcast data stream to
SUT |
Pass |
|
b.
WPA-PSK |
Pass |
|
- SUT sends multicast data
stream to STA2(Intersil) |
Pass |
|
- STA2 sends mulitcast data stream to
SUT |
Pass |
|
10.1 Non-Association with a
WEP AP - XP |
|
|
- Verify the STA does not
complete the association with the AP |
Pass |
|
10.2 Non-Association with an
AP not using WPA - XP |
|
|
- Verify the STA does not
complete the association with the AP |
Pass |
|
10.5.1 Non-Association with
PSK configured station - XP |
|
|
- Verify the STA does not
complete the association with the AP |
Pass |
|
10.5.2 Non-Association with a
TLS configured station |
|
|
- Verify the STA does not
complete the association with the AP |
Pass |
|
Cisco Client
eXtensions v2.0 |
|
|
|
6.3.0 AP Control of Client
Transmit Power[S31] |
Windows
XP |
Windows
2K |
|
6.3.1 TPC IE from multiple Aps - Use of correct power setting upon a
successful authentication |
|
|
|
1. Use a wireless sniffer to verify the client receives the TCP IE
from the access points |
Passed |
Passed |
|
2. Verify the client has set
its transmit power to the value contained in the IE from the AP it
associates to |
Passed |
Passed |
|
3. Roam to the other AP,
verify client has set its transmit power to the value contained in the
IE from the new AP |
Passed |
Passed |
|
6.3.2 Client uses the minimum power
limit set by the AP or configured power limit set by the client's
host |
|
|
|
- Upon successful association,
verify the client transmit power remains at or less than the value set
in the AP TPC value |
Passed |
Passed |
|
6.3.3 Client uses the maximum power
limit set by the AP or configured power limit set by the client's
host |
|
|
|
- Upon successful association,
verify the client transmit power changes to the value set on the
AP |
Passed |
Passed |
|
6.4.0 AP Assisted Roaming
[S32] |
|
|
|
6.4.1.1 Client uses the DDP packet to send
to the new AP the channel and SSID of the previous AP, and the amount
of time since losing association to the previous AP
|
|
|
|
- Upon successful association
to the new AP, use a wireless sniffer to
verify the client send the DDP information
packet |
Passed |
Passed |
|
contains the previous AP's radio channel, SSID and
length of time since the association was
lost. | ||
|
6.4.1.2 Client does not send DDP
information of the previous AP if it failed LEAP authentication to the
new AP |
|
|
|
- Upon successful association
to the new AP, use a wireless sniffer to
verify the client must NOT send an
information |
Passed |
Passed |
|
DDP packet to the new AP
containing the information about the AP it attempted but failed to
associate to | ||
|
6.4.1.3 Client roams to another AP in
125msecs or less when the radio channels are the
same |
|
|
|
- Verify the client roams from
AP1 to AP2 and resume sending the multicast data stream must not
exceed 125msecs |
Passed |
Passed |
|
6.4.1.4 Client roams to another AP in
<=125 msecs when the radio channel is at
opposite ends of frequency band |
|
|
|
- Verify the client roams from
AP1 to AP2 and resume sending the multicast data stream must not
exceed 125msecs |
Passed |
Passed |
|
6.5.0 Fast Reauthentication with CCKM
[S33] |
|
|
|
6.5.1.1 Single CCKM AP Initial
Authentication to SSID |
|
|
|
1. Verify connectivity, FTP
receive/transmit a file to a host on the wired network. Verify the
file is not corrupted. |
Passed |
Passed |
|
2. Verify the client can
receive a multicast data stream from a host on the wired
network. |
Passed |
Passed |
|
6.5.2.1 CCKM MN Fast Authentication -
Client Roaming |
|
|
|
1. Authenticate the client and
verify client can FTP receive/transmit to and from a host on the wired
network |
Passed |
Passed |
|
2. Verify the client can
receive a multicast data stream from a host on the wired
network. |
Passed |
Passed |
|
3. Cause the client to roam
repeatedly between the 2 APs and verify the
ACS Server is not being queried during
roaming |
Passed |
Passed |
|
4. Verify the client can still
FTP&Mcast receive/transmit data after
each roam |
Passed |
Passed |
|
5. Verify the time it takes to
roam from AP1 to AP2 is no greater than
125msecs |
Passed |
Passed |
|
6.5.3.1 Single CCKM AP Session
Timeout |
|
|
|
1. Upon successful
association, verify on the AP that the client is using CCKM with
CKIP/MIC enable |
Passed |
Passed |
|
2. Verify the client can FTP
receive/transmit a file to a host on the wired network. Verify the
file is not corrupted. |
Passed |
Passed |
|
3. Verify the client can
receive a multicast data stream from a host on the wired
network. |
Passed |
Passed |
|
4. Verify the client
re-authenticates at RADIUS session timeout |
Passed |
Passed |
|
5. Verify the client can still
FTP&Mcast receive/transmit after the
re-authentication |
Passed |
Passed |
|
6.6.0 PEAP Supplicant
[S34] |
|
|
|
6.6.1.1 PEAP Supplicant
Installation/Configuration |
|
|
|
1. PEAP-GTC authenticate the
client against a Win2K Active Directory |
Passed |
Passed |
|
2. Upon successful
association, verify client can pass FTP&Mcast receive/transmit data to a host on
the wired network |
Passed |
Passed |
|
6.6.1.2 One time password (Soft
Token) |
|
|
|
1. Verify the client logs in
successfully using the Soft Token OTP backend database, and receives
DHCP address |
Passed |
Passed |
|
2. Verify the client can FTP
receive/transmit a file to a host on the wired network. Verify the
file is not corrupted. |
Passed |
Passed |
|
6.6.1.4 PEAP Re-Authentication -
Roaming - Soft Token |
|
|
|
1. PEAP authenticate the
client using a soft token from an OTP server |
Passed |
Passed |
|
2. Verify connectivity, start
an FTP get file transfer from a host on the wired network to the
wireless client |
Passed |
Passed |
|
3. Initiate the roaming to the
2nd AP during the file transfer and verify the client roams and file
transfer continues |
Passed |
Passed |
|
6.7.0 WPA TKIP with LEAP and PEAP
[S35] |
|
|
|
6.7.1 Verify client can authenticate
using Cisco LEAP and use the new WPA Standard
TKIP |
|
|
|
1. Verify the client can FTP
receive/transmit a file to a host on the wired network. Verify the
file is not corrupted. |
Passed |
Passed |
|
2. Verify the client can
receive a multicast data stream from a host on the wired
network. |
Passed |
Passed |
|
6.7.2 Verify client can authenticate
using PEAP with EAP-GTC and use the new WPA Standard
TKIP |
|
|
|
1. Verify the client can FTP
receive/transmit a file to a host on the wired network. Verify the
file is not corrupted. |
Passed |
Passed |
|
2. Verify the client can
receive a multicast data stream from a host on the wired
network. |
Passed |
Passed |
|
6.8.0 Radio Measurement Requests
[S36] |
|
|
|
6.8.1.1 Beacon Report - Passive Scan,
Same Channel |
|
|
|
1. Use a wireless sniffer to verify the client performs the Beacon
measurements for the time duration interval of 125 TUs |
Passed |
Passed |
|
2. The client to performs a
passive scan.Verify the client does not send
a probe request |
Passed |
Passed |
|
3. Verify the client transmits
a Beacon Report Frame back to the requesting
AP |
Passed |
Passed |
|
4. Verify the Beacon Report
Frame contains all of the requirements as specified in CCXv2 spec part
S36.14 |
Passed |
Passed |
|
5. Verify that all
measurements are on the specified channel and correct signal strength
receives at -35 dBm |
Passed |
Passed |
|
6. Increase attenuation of
AP2's beacons by 20 dBm and verify the
client report its beacons at the new signal
strength |
Passed |
Passed |
|
6.8.1.2 Beacon Report - Beacon Table
Scan |
|
|
|
1. Verify the client does NOT
perform a new radio measurement when it receives the Beacon
Report Request from the AP |
Passed |
Passed |
|
2. Verify the client transmits
a Beacon Report that contains the current contents of its Beacon Table
without rescan |
Passed |
Passed |
|
3. Verify the Beacon Report
Frame contains all of the requirements as specified in CCXv2 spec part
S36.14 |
Passed |
Passed |
|
4. Use a wireless sniffer to verify the client sent the Beacon
Report within 50ms of the Request, and contains both
AP1&2 |
Passed |
Passed |
|
6.8.1.3 Beacon Report - Passive Scan,
Different Channel |
|
|
|
1. Use a wireless sniffer to verify the client performs the Beacon
measurements for the time duration interval of 125 TUs |
Passed |
Passed |
|
2. Verify the client performs
a passive measurement on the non-serving channel, temporarily
buffering outgoing FTP traffic |
Passed |
Passed |
|
3. Verify the client transmits
a Beacon Report Frame back to the requesting
AP |
Passed |
Passed |
|
4. Verify the Beacon Report
Frame contains all of the requirements as specified in CCXv2 spec part
S36.14 |
Passed |
Passed |
|
5. Verify the all measurements
are on the specified channel and correct signal strength receives at
-35 dBm |
Passed |
Passed |
|
6. Decrease attenuation of
AP2's beacons by 20 dBm and verify the
client report its beacons at the new signal
strength |
Passed |
Passed |
|
6.8.1.4 Beacon Report - Active Scan,
Different Channel |
|
|
|
1. Use a wireless sniffer to verify the client performs the Beacon
measurements for the time duration interval of 250 TUs |
Passed |
Passed |
|
2. Verify the client performs
a active measurement on the non-serving channel, temporarily buffering
outgoing FTP traffic |
Passed |
Passed |
|
3. Verify the client transmits
a Beacon Report Frame back to the requesting
AP |
Passed |
Passed |
|
4. Verify the Beacon Report
Frame contains all of the requirements as specified in CCXv2 spec part
S36.14 |
Passed |
Passed |
|
5. Verify the all measurements
are on the specified channel and correct signal strength receives at
-35 dBm |
Passed |
Passed |
|
6. Decrease attenuation of
AP2's beacons by 20 dBm and verify the
client report its beacons at the new signal
strength |
Passed |
Passed |
|
6. Start a large FTP file
transfer from the client to a wired host, send another Frame Report
Request which specifies a |
Passed |
Passed |
|
different channel scan for a duration of 5000 TUs, and verify client ignore the request to
perform measurement. |
Passed |
Passed |
|
6.8.3.1 Channel Load Report - Same
Channel |
|
|
|
1. Use a wireless sniffer to verify the client performs the Channel
Load measurements for time duration interval of 100 TUs |
Passed |
Passed |
|
2. Verify the client performs
the measurement on the current serving channel
only |
Passed |
Passed |
|
3. Verify that the client
under test properly reports the total 802.11 channel busy fraction from AP1, AP2 and CL2.
|
Passed |
Passed |
|
4. Verify the Channel Load
Report contains all the requirements as specified in CCXv2 spec part
S36.16 |
Passed |
Passed |
|
5. Wait for the FTP file
transfer to complete, send another Channel Load Report Request to the
client under test which |
Passed |
Passed |
|
specifies a same channel scan for a duration of 100
TUs. Use wireless sniffer to verify the second Channel Load
Report |
Passed |
Passed |
|
reflect the fact that the channel was not busy
during the scan and report the Channel Load
accordingly. |
Passed |
Passed |
|
6.8.3.2 Channel
Load Report - Different Channel |
|
|
|
1. Use a wireless sniffer to verify the client performs the Channel
Load measurements for time duration interval of 100 TUs |
Passed |
Passed |
|
2. Verify the client performs
the measurement on the non-serving channel, temporarily buffer the FTP
file transfer |
Passed |
Passed |
|
3. Verify that the client
under test properly reports the total 802.11 channel busy fraction from AP1, AP2 and CL2.
|
Passed |
Passed |
|
4. Verify the Channel Load
Report contains all the requirements as specified in CCXv2 spec part
S36.16 |
Passed |
Passed |
|
5. Wait for the FTP file
transfer to complete, send another Channel Load Report Request to the
client under test which |
Passed |
Passed |
|
specifies a different channel scan for a duration
of 100 TUs. Use wireless sniffer to verify the second Channel
Load |
Passed |
Passed |
|
Report
reflect the fact that the channel was not busy during the scan and
report the Channel Load accordingly. |
Passed |
Passed |
|
6. Start FTP file transfers
from the client under test and client#2 to a host on the wired
network. Send another Channel |
Passed |
Passed |
|
Load Report
Request to the client under test which specifies a same channel scan
for a duration of 5000 TUs and
verify |
Passed |
Passed |
|
the client ignores the Channel Load
Request. |
Passed |
Passed |
|
6.8.4.1 Noise Histogram Report - Same
Channel |
|
|
|
1. Verify the client performs
the Noise Histogram measurements for the time interval of 20 TU’s |
Passed |
Passed |
|
2. Verify the client performs
the measurement on the current serving channel
only |
Passed |
Passed |
|
3. Verify the Noise Histogram
Report contains all the requirements as specified in CCXv2 spec part
S36.17 |
Passed |
Passed |
|
6.8.4.2 Noise Histogram Report -
Different Channel |
|
|
|
1. Verify the client performs
the Noise Histogram measurements for the time interval of 20 TU’s |
Passed |
Passed |
|
2. Verify the client performs
the measurement on non-serving channel(9) only, temporarily buffer the
FTP file transfer |
Passed |
Passed |
|
3. Start another FTP file
transfers from client to a wired host network and send a Noise
Histogram Request to the client |
Passed |
Passed |
|
which specifies a scan on channel 9 for a duration
of 5000 TUs and verify the client ignores
this request. |
Passed |
Passed |
|
6.8.5.1 Multiple Radio Measurement
Requests - Same Channel |
|
|
|
1. Verify the client performs
the Radio measurements for the time interval of 125 TU’s |
Passed |
Passed |
|
2. Verify the client performs
the measurement on the current serving channel
only |
Passed |
Passed |
|
3. Verify that the client
under test properly reports the total 802.11 channel busy fraction
from AP1, AP2 and CL2 |
Passed |
Passed |
|
4. Verify that the client
properly reports all Beacons received during the time
interval |
Passed |
Passed |
|
5. Verify that the client
properly reports all Frames heard during the time
interval |
Passed |
Passed |
|
6.8.5.2 Multiple Radio Measurement
Requests - Different Channel |
|
|
|
1. Verify the client performs
the Radio measurements for the time interval of 125 TU’s |
Passed |
Passed |
|
2. Verify the client performs
the measurement on non-serving channel only, temporarily buffer the
FTP file transfer traffic |
Passed |
Passed |
|
3. Verify that the client
under test properly reports the total 802.11 channel busy fraction
from AP1, AP2 and CL2 |
Passed |
Passed |
|
4. Verify that the client
properly reports all Beacons received during the time
interval |
Passed |
Passed |
|
5. Verify that the client
properly reports all Frames heard during the time
interval |
Passed |
Passed |
|
6. Start another FTP file
transfer from the client to a wired host network and send a Radio
Measurement Request to client |
Passed |
Passed |
|
which specifies a different channel scan and a
duration of 5000 TUs. Verify the client
ignores this request. |
Passed |
Passed |
|
6.9.0
|
|
|
|
6.9.1 Client
communicates its |
|
|
|
1. Associate the client to the
first AP, verify via a wireless sniffer that
correct DDP packet is being sent to the AP |
Passed |
Passed |
|
2. Force client to roam to a
2nd AP, verify via a wireless sniffer that
correct DDP packet is being sent to the AP |
Passed |
Passed |
|
6.10.0 QoS
Parameter Set Element [S39] |
|
|
|
6.10.1 Client
adopts Cwmin, Cwmax, AIFSN (fixed slot time) values sent by the
Access Points |
|
|
|
1. Associate the DUT and a
non-CCX clients to AP1, perform a 20MB ftp transfer from both clients
to a wired host network |
Passed |
Passed |
|
at the
same time and record the performance of the DUT: | ||
|
2. Now associate both clients
to AP2, perform a 20MB ftp transfer from both clients to same wired
network at the same |
Passed |
Passed |
|
time and record the performance of the DUT. Verify
the DUT's performance is degraded by at
least 10%. |
|
Cisco Client
eXtensions CCX
v1 | ||
|
|
WinXP |
Win2K |
|
4.1.1 Fragmentation
support |
Pass |
Pass |
|
4.1.2 CTS and RTS
support |
Pass |
Pass |
|
4.2 Active
Scanning |
|
|
|
4.2.1 Client ignore missing SSID in
Beacons |
Pass |
Pass |
|
4.2.2 Do not ROAM with
multicast/broadcast decrypt error in VLAN
environment |
Pass |
Pass |
|
4.2.3 Client to use SSID in Probe
Request |
Pass |
Pass |
|
4.2.4 Multiple SSID support in
Configuration Utility |
Pass |
Pass |
|
4.4 802.1x Security
Compliance/CKIP Support/40 and 128-bit WEP Keys/LEAP
support |
|
|
|
4.4.1.1 40-bit WEP (Open
Authentication) with MIC/CKIP enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
disabled |
Pass |
Pass |
|
2. Verify connectivity and FTP
& Mcast transfers with MIC/CKIP
enabled |
Pass |
Pass |
|
3. Disable MIC/CKIP and
re-verify connectivity and FTP & Mcast
transfers |
Pass |
Pass |
|
4.4.1.2 40-bit WEP (Open
Authentication, with Different Transmit Keys) WEP Key
1&2 |
|
|
|
- Verify connectivity and FTP
& Mcast
transfers |
Pass |
Pass |
|
4.4.1.3 40-bit WEP (Shared-Key
Authentication) with MIC an CKIP enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
disabled |
Pass |
Pass |
|
2. Verify connectivity and FTP
& Mcast transfers with MIC/CKIP
enabled |
Pass |
Pass |
|
3. Disable MIC/CKIP and
re-verify connectivity and FTP & Mcast
transfers |
Pass |
Pass |
|
4.4.1.4 40-bit WEP (Shared-Key
Authentication, with Different Transmit Keys) WEP Key
3&4 |
|
|
|
- Verify connectivity and FTP
& Mcast
transfers |
Pass |
Pass |
|
4.4.1.5 128-bit WEP (Open
Authentication) with MIC and CKIP enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
disabled |
Pass |
Pass |
|
2. Verify connectivity and FTP
& Mcast transfers with MIC/CKIP
enabled |
Pass |
Pass |
|
3. Disable MIC/CKIP and
re-verify connectivity and FTP & Mcast
transfers |
Pass |
Pass |
|
4.4.1.6 128-bit WEP (Open
Authentication, Different Transmit Keys) WEP Key
1&2 |
|
|
|
- Verify connectivity and FTP
& Mcast
transfers |
Pass |
Pass |
|
4.4.1.7 128-bit WEP (Shared-Key
Authentication) with MIC and CKIP enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
disabled |
Pass |
Pass |
|
2. Verify connectivity and FTP
& Mcast transfers with MIC/CKIP
enabled |
Pass |
Pass |
|
3. Disable MIC/CKIP and
re-verify connectivity and FTP & Mcast
transfers |
Pass |
Pass |
|
4.4.1.8 128-bit WEP (Shared-Key
Authentication, Different Transmit Keys) WEP Key
3&4 |
|
|
|
- Verify connectivity and FTP
& Mcast
transfers |
Pass |
Pass |
|
4.4.2.1 LEAP (Using a 40-bit WEP
Broadcast Key) |
|
|
|
1. Verify connectivity
and FTP & Mcast
transfers |
Pass |
Pass |
|
2. Configure session
timeout to 60 seconds on Radius and verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
3. FTP and Mcast transfers with MIC/CKIP
enable |
Pass |
Pass |
|
4. Configure broadcast
key period of 30 seconds on AP and verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
4.4.2.2 LEAP (Using a 128-bit WEP
Broadcast Key) |
|
|
|
1. Verify connectivity
and FTP & Mcast
transfers |
Pass |
Pass |
|
2. Configure session
timeout to 60 seconds on Radius and verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
3. FTP and Mcast transfers with MIC/CKIP
enable |
Pass |
Pass |
|
4. Configure broadcast
key period of 30 seconds on AP and verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
4.4.4.1 EAP-TLS (Using a 40-bit
Broadcast Key, Open Authentication) with MIC and CKIP
enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast
transfers |
Pass |
XP Only |
|
2. Verify connectivity
and FTP & Mcast transfers with MIC
enabled |
Pass |
XP Only |
|
3. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
enabled |
Pass |
XP Only |
|
4. Configure broadcast
key period of 30 seconds on AP and verify connectivity and FTP &
Mcast transfers |
Pass |
XP Only |
|
5. Configure session
timeout to 60 seconds on Radius and verify connectivity and FTP &
Mcast transfers |
Pass |
XP Only |
|
4.4.4.2 EAP-TLS (Using a 128-bit
Broadcast Key, Open Authentication) with MIC and CKIP
enabled |
|
|
|
1. Verify connectivity
and FTP & Mcast
transfers |
Pass |
XP Only |
|
2. Verify connectivity
and FTP & Mcast transfers with MIC
enabled |
Pass |
XP Only |
|
3. Verify connectivity
and FTP & Mcast transfers with MIC/CKIP
enabled |
Pass |
XP Only |
|
4. Configure broadcast
key period of 30 seconds on AP and verify connectivity and FTP &
Mcast transfers |
Pass |
XP Only |
|
5. Configure session
timeout to 60 seconds on Radius and verify connectivity and FTP &
Mcast transfers |
Pass |
XP Only |
|
4.4.5 Mixed Cell (WEP and Non-WEP)
Functional Tests |
|
|
|
4.4.5.1 40-bit WEP (Mixed-CELL
Allowed) |
|
|
|
1. Set the use of
encryption on AP to Optional then verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
2. Set a matching static
WEP key on the client STA and verify it must not associate to the
AP |
Pass |
Pass |
|
4.4.5.3 128-bit WEP (Mixed-CELL
Allowed) |
|
|
|
1. Set the use of
encryption on AP to Optional then verify connectivity and FTP &
Mcast transfers |
Pass |
Pass |
|
2. Set a matching static
WEP key on the client STA and verify it must not associate to the
AP |
Pass |
Pass |
|
4.4.5.5 LEAP 128-Bit WEP Key (Mixed
Cell) - set encryption to Optional |
|
|
|
- Configure the client
for LEAP authentication and verify it must not associate to the
AP |
Pass |
Pass |
|
4.4.6 Roaming with Security Features
Enabled (128-Bit WEP key, MIC, CKIP, Broadcast-Key)
EAP-TLS |
|
|
|
1. Enable MIC/CKIP and
broadcast key rotation of 30 seconds: verify connectivity and
FTP/Mcast
transfers |
Pass |
XP Only |
|
2. Initiate a roam:
Verify general connectivity |
Pass |
XP Only |
|
3. Initiate another roam
during FTP transfer: The FTP transfers succeed after the
roam |
Pass |
XP Only |
|
4. Intiate another roam during Mcast transfer: The multicast packets must be
received after the roam |
Pass |
XP Only |
|
4.4.7 Performance Security Feature
Enabled (128-Bit WEP key, MIC, CKIP)
EAP-TLS |
|
|
|
1. Receive throughput from AP
with MIC/CKIP disable |
Pass |
XP Only |
|
2. Receive throughput from AP
with only MIC enable |
Pass |
XP Only |
|
3. Receive throughput from AP
with MIC and CKIP enable |
Pass |
XP Only |
|
4.4.7.1 Incrementing
IV |
|
|
|
1. CKIP disabled: IV can be
random or increments by one |
Pass |
Pass |
|
2. CKIP enabled: IV increments
by one on each transmit |
Pass |
Pass |
|
4.5 Rogue AP Reporting
Support |
|
|
|
4.5.1 LEAP with invalid
Authentication, Failure code 0x01 (Invalid authentication
type) |
Pass |
Pass |
|
4.5.2 Authentication Timeout,
Failure code 0x02 (Authentication timeout) |
Pass |
Pass |
|
4.5.3 Challenge from AP Failed,
Failure code 0x03 (Challenge from AP failed) |
Pass |
Pass |
|
SECTION
5.0: AP TEST
CONFIGURATIONS - 802.11a |
|
SECTION
5.0: AP TEST
CONFIGURATIONS - 802.11b |
|
|
|
| ||
|
Configuration
#S1 - Proxim
AP2000 |
|
Configuration
#S1 - AGERE AP-1000 |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[10.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[2.3] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[13.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[2.2] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.0] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.3] |
Pass |
|
Configuration
#S2 - Intermec Mobilan
2106 |
|
Configuration
#S2 - DLINK DWL-900AP |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[9.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[1.4] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[9.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[2.3] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.10] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.32] |
Pass |
|
Configuration
#S3 - Cisco 1220 |
|
Configuration
#S3 - Cisco Aironet
350 |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[6.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[1.2] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[6.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[2.8] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[0.90] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.30] |
Pass |
|
Configuration
#S4 - Atheros
AR5001 |
|
Configuration
#S4 - Symbol Spectrum24 - 4121 AP |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[15.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[0.80] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[9.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[1.1] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.0] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.28] |
Pass |
|
Configuration
#S5 - PROXIM AP2000 |
|
Configuration
#S5 - AGERE AP-1000 |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[9.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[2.5] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[11.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[3.1] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.0] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.25] |
Pass |
|
Configuration
#S6 - Cisco 1220 |
|
Configuration
#S6 - DLINK DWL-900AP |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[8.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[1.2] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[14.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[0.55] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[0.90] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.34] |
Pass |
|
Configuration
#S7 - Atheros
AR5001 |
|
Configuration
#S7 - Cisco Aironet
350 |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[7.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[1.2] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[15.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[2.0] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.10] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.45] |
Pass |
|
Configuration
#S8 - Intermec Mobilan
2106 |
|
Configuration
#S8 - Symbol Spectrum24 - 4121 AP |
|
|
Association |
Pass |
Association |
Pass |
|
- Data
Transfer 1: FileSendlong rx
[8.0] |
Pass |
- Data
Transfer 1: FileSendlong rx
[1.7] |
Pass |
|
- Data
Transfer 2: FileSendlong tx
[13.0] |
Pass |
- Data
Transfer 2: FileSendlong tx
[0.8] |
Pass |
|
- Data
Transfer 3: InquiryLong tx
[1.20] |
Pass |
- Data
Transfer 3: InquiryLong tx
[0.30] |
Pass |
|
Section 5.3.1
Roaming |
|
Section 5.3.1
Roaming |
|
|
- Shut
OFF Atheros
AR5001 |
Pass |
- Shut
OFF Agere
AP-1000 |
Pass |
|
- Shut
OFF Cisco 1220 |
Pass |
- Shut
OFF Cisco350 AP |
Pass |
|
- Shut
OFF Intermec Mobilan
2106 |
Pass |
- Shut
OFF DLINK DWL-900AP |
Pass |
|
- Shut
OFF Proxim
AP2000 |
Pass |
- Shut
OFF Symbol Spectrum24 - 4121 AP |
Pass |
|
Section 5.3.2
Data Payload Encapsulation |
|
Section 5.3.2
Data Payload Encapsulation |
|
|
- IPX
Ethernet 802.2 tx |
Pass |
- IPX
Ethernet 802.2 tx |
Pass |
|
- IPX
Ethernet 802.2 rx |
Pass |
- IPX
Ethernet 802.2 rx |
Pass |
|
- IPX
Ethernet 802.3 tx |
Pass |
- IPX
Ethernet 802.3 tx |
Pass |
|
- IPX
Ethernet 802.3 rx |
Pass |
- IPX
Ethernet 802.3 rx |
Pass |
|
- IPX
Ethernet 802.II tx |
Pass |
- IPX
Ethernet 802.II tx |
Pass |
|
- IPX
Ethernet 802.II rx |
Pass |
- IPX
Ethernet 802.II rx |
Pass |
|
Section 5.3.3
Broadcast/Multicast Reception |
|
Section 5.3.3
Broadcast/Multicast Reception |
|
|
-
Proxim AP2000 MCS1: UDP RealAud [0.05] |
Pass |
-
Agere AP-1000 MCS1: UDP RealAud [0.05] |
Pass |
|
-
Intermec 2106 MCS2: UDP
RealAud [0.05] |
Pass |
-
DLINK DWL-900AP MCS2: UDP
RealAud [0.05] |
Pass |
|
-
Cisco 1220 AP MCS3: UDP
RealAud [0.05] |
Pass |
-
Cisco350 AP MCS3: UDP
RealAud [0.05] |
Pass |
|
-
Atheros AR5001 MCS4: UDP RealAud [0.05] |
Pass |
-
Symbol Spectrum 24 MCS4:
UDP RealAud
[0.05] |
Pass |
|
Section 5.3.4
Negative Tests |
|
Section 5.34
Negative Tests |
|
|
-
Negative: Wrong
ESSID |
Pass |
-
Negative: Wrong
ESSID |
Pass |
|
-
Negative: Wrong case in
ESSID |
Pass |
-
Negative: Wrong case in
ESSID |
Pass |
|
-
Negative: ESSID
substring |
Pass |
-
Negative: ESSID
substring |
Pass |
|
-
Negative: WEP key
mismatch |
Pass |
-
Negative: WEP key
mismatch |
Pass |
|
-
Negative: WEP Station/AP
mismatch |
Pass |
-
Negative: WEP Station/AP
mismatch |
Pass |
|
SECTION
6.0: IBSS TEST
CONFIGURATIONS |
|
SECTION
6.0: IBSS TEST
CONFIGURATIONS |
|
|
|
| ||
|
Section 6.1 -
Active Scan Tests |
|
Section 6.1 -
Active Scan Tests |
|
|
Creator STA = Station Under
Test |
Pass |
Creator STA = Station Under Testall else default |
Pass |
|
Join STA = Intersil 37703C |
Pass |
Join STA = Symbol
(LA-4121)---> (Frag: 384); (RTS:
Off) |
Pass |
|
Verify basic rates using
sniffer |
Pass |
Verify basic rates using
sniffer |
Pass |
|
Verify SUT responds with a
valid response to probe |
Pass |
Verify SUT responds with a
valid response to probe |
Pass |
|
Verify the channel in
beacon frame is correct |
Pass |
Verify the channel in
beacon frame is correct |
Pass |
|
Verify BSSID is a random
value after restart |
Pass |
Verify BSSID is a random
value after restart |
Pass |
|
FileSendS from Intersil to SUT (Within 90
seconds) |
Pass |
FileSendS from Symbol to SUT(Within
90 seconds) |
Pass |
|
FileSendS from SUT to Intersil (Within 90
seconds) |
Pass |
FileSendS from SUT to Symbol(Within
90 seconds) |
Pass |
|
Disable Intersil and verify different BSSID after
restart |
Pass |
Section 6.2 -
Passive Scan Tests |
|
|
Section 6.2 -
Passive Scan Tests |
|
Creator STA = Station Under Test
|
Pass |
|
Creator STA = Station Under
Test |
Pass |
Join STA = Intel Pro 2011B (Frag: Off); (RTS:
300) |
Pass |
|
Join STA = Atheros 5001X |
Pass |
Verify basic rates using
sniffer |
Pass |
|
Verify basic rates using
sniffer |
Pass |
Verify the channel in
beacon frame is correct |
Pass |
|
Verify the channel in
beacon frame is correct |
Pass |
Verify BSSID is a random
value after restart |
Pass |
|
Verify BSSID is a random
value after restart |
Pass |
FileSendS from Intel to SUT(Within
90 seconds) |
Pass |
|
FileSendS from Atheros to SUT (Within 90
seconds) |
Pass |
FileSendS from SUT to Intel(Within
90 seconds) |
Pass |
|
FileSendS from SUT to Atheros (Within 90
seconds) |
Pass |
Disable 3COM and verify
different BSSID after restart |
Pass |
|
Disable Atheros and verify different BSSID after
restart |
Pass |
Section 6.3 -
IBSS WEP ON Tests |
|
|
Section 6.4 -
IBSS WEP ON Tests |
|
Creator STA = Intersil v2.5 |
Pass |
|
Creator STA = Intel
5000 |
Pass |
Join STA = Cisco 350 (Frag: Off); (RTS:
300) |
Pass |
|
Join STA = Cisco
AIR-CB20A |
Pass |
Join STA = Station Under Test (All
default) |
Pass |
|
Join STA = Station Under Test (all
default) |
Pass |
Verify basic rates
enumerated in beacon using sniffer |
Pass |
|
Verify basic rates
enumerated in beacon using sniffer |
Pass |
Verify beacons fairly
distributed |
Pass |
|
Verify beacons fairly
distributed |
Pass |
SI3DT1: FileSendS from Cisco to SUT
[1.6] |
Pass |
|
SI3DT1: FileSendS from Cisco to SUT
[9.0] |
Pass |
SI3DT2: FileSendS from SUT to Cisco
[2.8] |
Pass |
|
SI3DT2: FileSendS from SUT to Cisco
[9.0] |
Pass |
SI3DT3: Multicast RealAud Test
[0.05] |
Pass |
|
SI3DT3: Multicast RealAud Test
[0.05] |
Pass |
SI3DT4: Multicast RealAud Test
[0.05] |
Pass |
|
SI3DT4: Multicast RealAud Test
[0.05] |
Pass |
STA continue to beacons
when Intersil and Cisco are
off |
Pass |
|
STA continue to beacons
when Intel and Cisco are off |
Pass |
Section 6.4 -
IBSS WEP OFF Tests |
|
|
Section 6.5 -
IBSS WEP OFF Tests |
|
Creator STA = Cirrus
Bodega |
Pass |
|
Creator STA = Intel
5000 |
Pass |
Join STA = Cisco
350 |
Pass |
|
Join STA = Cisco
AIR-CB20A |
Pass |
Join STA = Station Under Test (All
default) |
Pass |
|
Join STA = Station Under Test (all
default) |
Pass |
Verify rates using sniffer |
Pass |
|
Verify rates using sniffer |
Pass |
Verify beacons fairly
distributed |
Pass |
|
Verify beacons fairly
distributed |
Pass |
SI4DT1: FileSendS from Cirrus to SUT
[4.0] |
Pass |
|
SI4DT1: FileSendS from Intel to SUT
[11.0] |
Pass |
SI4DT2: FileSendS from SUT to Cirrus
[2.7] |
Pass |
|
SI4DT2: FileSendS from SUT to Intel
[11.0] |
Pass |
SI4DT3: FileSendS from Cisco to SUT [1.7] |
Pass |
|
SI4DT3: FileSendS from Cisco to SUT
[10.0] |
Pass |
SI4DT4: FileSendS from SUT to Cisco
[4.0] |
Pass |
|
SI4DT4: FileSendS from SUT to Cisco
[10.0] |
Pass |
STA continue to beacons
when Cirrus and Cisco are off |
Pass |
|
STA continue to beacons
when Intel and Cisco are off |
Pass |
Section 6.5 -
Re-Join Tests |
|
|
Section 6.5 -
Re-Join Tests |
|
Creator STA = Intersil |
Pass |
|
Creator STA = Intel
5000 |
Pass |
Join STA =
Symbol |
Pass |
|
Join STA = Intersil 37703C |
Pass |
Join STA = Station Under
Test |
Pass |
|
Join STA = Station Under
Test |
Pass |
Move SUT out of range and
verify not receiving beacons |
Pass |
|
Move SUT out of range and
verify not receiving beacons |
Pass |
Move SUT back into range,
verify connection to 3 STAs |
Pass |
|
Move SUT back into range,
verify connection to 3 STAs |
Pass |
|
|
|
Section 7.2 -
Cross Band Roaming |
|
|
|
|
AP#1[802.11a] Cisco Aironet 1220 AP |
Pass |
|
|
|
AP#2[802.11b] Agere AP1000 |
Pass |
|
|
|
AP#3[802.11a]
|
Pass |
|
|
|
AP#4[802.11b] Dlink DWL-900AP |
Pass |
|
|
|
LogName |
Total |
Passed |
Failed |
Warned |
|
1c_wlan_ssid.htm |
10 |
10 |
0 |
0 |
|
1c_wlan_associatetime.htm |
5 |
5 |
0 |
0 |
|
1c_wlan_powermode.htm |
4 |
4 |
0 |
0 |
|
2m_wlan_wep.htm |
9 |
9 |
0 |
0 |
|
1c_wlan_bssidlist.htm |
5 |
3 |
2 |
0 |
|
2m_wlan_adhoc.htm |
10 |
0 |
7 |
3 |
|
1c_wlan_mediaevents.htm |
11 |
9 |
0 |
2 |
|
1c_wlan_disassociate.htm |
15 |
15 |
0 |
0 |
|
2m_WOLMagicPacket.htm |
3 |
3 |
0 |
0 |
|
2m_WOLPattern.htm |
4 |
4 |
0 |
0 |
|
2c_PMStandby.htm |
25 |
21 |
0 |
4 |
|
2c_PMHibernate.htm |
35 |
29 |
0 |
6 |
|
2c_TransferData.htm |
25 |
22 |
0 |
3 |
|
2c_StressClient.htm |
17 |
17 |
0 |
0 |
|
2c_Simultaneous.htm |
30 |
30 |
0 |
0 |
|
2c_SendRecv1.htm |
408 |
397 |
0 |
11 |
|
2c_SendPackets.htm |
56 |
52 |
0 |
4 |
|
2c_RecvMulticast.htm |
181 |
181 |
0 |
0 |
|
2c_ReceivePackets.htm |
65 |
65 |
0 |
0 |
|
2c_Priority.htm |
7 |
7 |
0 |
0 |
|
2c_PerformanceProfile.htm |
31 |
31 |
0 |
0 |
|
2c_PerformanceBlast.htm |
15 |
15 |
0 |
0 |
|
2c_OffloadCheckSum.htm |
4 |
4 |
0 |
0 |
|
2c_OffloadLargeSend.htm |
4 |
4 |
0 |
0 |
|
2c_OffloadTaskMisc.htm |
4 |
4 |
0 |
0 |
|
2c_LoadUnload.htm |
164 |
163 |
0 |
1 |
|
2c_Deadlock.htm |
10 |
10 |
0 |
0 |
|
2c_CheckConnections.htm |
10 |
9 |
0 |
1 |
|
2c_AddressChange.htm |
73 |
73 |
0 |
0 |
|
1c_SetMulticast.htm |
283 |
283 |
0 |
0 |
|
1c_Reset.htm |
149 |
149 |
0 |
0 |
|
1c_SetLookahead.htm |
75 |
75 |
0 |
0 |
|
1c_OidsNdisRequest.htm |
83 |
83 |
0 |
0 |
|
1c_OffloadInvalid.htm |
4 |
4 |
0 |
0 |
|
1c_LoopbackStress.htm |
19 |
19 |
0 |
0 |
|
1c_LoopbackSend.htm |
130 |
130 |
0 |
0 |
|
1c_FaultHandling.htm |
30 |
30 |
0 |
0 |
|
1c_KernelCalls.htm |
8 |
7 |
0 |
1 |
|
1c_64BitOIDs.htm |
11 |
5 |
0 |
6 |
|
1c_InitTime.htm |
25 |
25 |
0 |
0 |
|
2c_MediaCheck.htm |
26 |
24 |
0 |
2 |
|
WHQLConfigCheck.htm |
10 |
9 |
1 |
0 |
|
Total |
2093 |
2039 |
10 |
44 |
|
LogName |
Total |
Passed |
Failed |
Warned |
|
2c_PMStandby.htm |
26 |
26 |
0 |
0 |
|
2c_PMHibernate.htm |
35 |
35 |
0 |
0 |
|
1c_InitTime.htm |
25 |
25 |
0 |
0 |
|
2c_MediaCheck.htm |
26 |
25 |
0 |
1 |
|
1c_wlan_ssid.htm |
9 |
9 |
0 |
0 |
|
1c_wlan_powermode.htm |
4 |
4 |
0 |
0 |
|
1c_wlan_associatetime.htm |
5 |
5 |
0 |
0 |
|
2m_wlan_wep.htm |
9 |
9 |
0 |
0 |
|
1c_wlan_bssidlist.htm |
5 |
3 |
2 |
0 |
|
1c_wlan_mediaevents.htm |
11 |
9 |
0 |
2 |
|
1c_wlan_disassociate.htm |
15 |
15 |
0 |
0 |
|
2m_WOLMagicPacket.htm |
3 |
2 |
0 |
1 |
|
2c_TransferData.htm |
25 |
24 |
0 |
1 |
|
2c_StressClient.htm |
17 |
17 |
0 |
0 |
|
2c_Simultaneous.htm |
30 |
30 |
0 |
0 |
|
2c_SendRecv1.htm |
408 |
396 |
0 |
12 |
|
2c_SendPackets.htm |
56 |
36 |
0 |
20 |
|
2c_RecvMulticast.htm |
182 |
180 |
0 |
2 |
|
2c_ReceivePackets.htm |
65 |
63 |
0 |
2 |
|
2c_Priority.htm |
7 |
7 |
0 |
0 |
|
2c_PerformanceProfile.htm |
31 |
31 |
0 |
0 |
|
2c_PerformanceBlast.htm |
15 |
15 |
0 |
0 |
|
2c_OffloadTaskMisc.htm |
4 |
4 |
0 |
0 |
|
2c_OffloadLargeSend.htm |
4 |
4 |
0 |
0 |
|
2c_OffloadCheckSum.htm |
4 |
4 |
0 |
0 |
|
2c_LoadUnload.htm |
164 |
163 |
0 |
1 |
|
2c_Deadlock.htm |
10 |
10 |
0 |
0 |
|
2c_ShortPackets.htm |
3 |
3 |
0 |
0 |
|
2c_CheckConnections.htm |
10 |
10 |
0 |
0 |
|
1c_SetMulticast.htm |
289 |
289 |
0 |
0 |
|
1c_SetLookahead.htm |
75 |
75 |
0 |
0 |
|
1c_Reset.htm |
149 |
149 |
0 |
0 |
|
1c_OidsNdisRequest.htm |
83 |
83 |
0 |
0 |
|
1c_OffloadInvalid.htm |
4 |
4 |
0 |
0 |
|
1c_LoopbackStress.htm |
19 |
19 |
0 |
0 |
|
1c_LoopbackSend.htm |
130 |
129 |
0 |
1 |
|
1c_FaultHandling.htm |
30 |
30 |
0 |
0 |
|
1c_KernelCalls.htm |
8 |
6 |
0 |
2 |
|
1c_64BitOIDs.htm |
11 |
5 |
0 |
6 |
|
2c_AddressChange.htm |
73 |
72 |
0 |
1 |
|
2m_wlan_adhoc.htm |
10 |
3 |
7 |
0 |
|
WHQLConfigCheck.htm |
10 |
9 |
1 |
0 |
|
Total |
2099 |
2037 |
10 |
52 |
|
LogName |
Total |
Passed |
Failed |
Warned |
|
2m_strsb.leth4 |
6 |
6 |
0 |
0 |
|
1c_ginfo.leth |
55 |
43 |
12 |
0 |
|
1c_gstat.leth |
61 |
49 |
12 |
0 |
|
1c_looka.leth |
58 |
58 |
0 |
0 |
|
1c_multi.leth |
214 |
214 |
0 |
0 |
|
1c_reset.leth |
143 |
143 |
0 |
0 |
|
1c_sends.leth |
14 |
14 |
0 |
0 |
|
1c_srecv.leth |
182 |
182 |
0 |
0 |
|
2m_pblst.leth |
9 |
9 |
0 |
0 |
|
2m_pprof.leth |
65 |
65 |
0 |
0 |
|
2m_srecv.leth4 |
322 |
285 |
25 |
27 |
|
2m_srrdi.leth4 |
50 |
39 |
8 |
3 |
|
2m_stndb.leth4 |
0 |
0 |
0 |
4 |
|
1c_filtr.leth |
320 |
320 |
0 |
0 |
|
2m_strsc.leth4 |
11 |
11 |
0 |
0 |
|
2m_strss.leth4 |
6 |
6 |
0 |
0 |
|
nd_cli.log |
9 |
9 |
0 |
0 |
|
2m_addre.leth4 |
1 |
1 |
0 |
0 |
|
2m_hiber.leth4 |
1 |
1 |
0 |
0 |
|
Total |
1527 |
1455 |
57 |
34 |
Copyright © 2001-2004 Broadcom Corporation